********************************
ECpvx Version 1.00.0 - First release
********************************
1- First release 1.00.0 based on ECpv 1.70.1

********************************
Version 1.01.0 based on version 1.00.0
********************************
New features:
1- INVT inverter support added
2- Huawei smartlogger IO support added
3- Inverter Secondary control added

********************************
Version 1.01.1 based on version 1.01.0
********************************
1- Info text and mode text for grid, battery and genset is updated. 

********************************
Version 1.02.0 based on version 1.01.1
********************************
1- AIO Support added. 
2- Update made to the ABB M4M-30 support.
3- Elgris Smartmeter support added.
4- Configurable Modbus area added.
5- Sum of Genset and Grid power and reactive power added to Modbus. 
6- Update made for Elgris smartmeter.  
7- Modbus proprietary page 5 and 6 enable/disable was not saved in settings backup.
8- Load depend start will use start target all time when grid has being connected and disconnected.   
9- Update made to automatically scheduled NTP.
10- Carlo Gavazzi power meter added 
12- DEIF ML2 btb position added as IO module
13- Hide of IO readings was incorrect when selecting huawei smartlogger
14- DSE8680 btb position added as IO module
15- Further update made to automatically scheduled NTP.
16- Soluzione Solare LiteMeter Pro support.
17- Support of Woodward Easygen3000XT genset controller. 
18- Support of Hukseflux SR05 added. 
19- Huawei Smartlogger added as an option for genset meter protocol selection.
20- Support of Soluzione Solare Sunmeter Pro added. 
21- Updates made for the Litemeter pro support.
22- Updates made for the Goodwe MT inverter support.
23- Update made to the Phoenix EMPro support.
24- Update made to the Accuvim EV300 handling.

************************************************
Version 1.03.0 based on version 1.02.0
************************************************
1- P/Q Mains reference manipulation via RRCR Ana scheme added.
2- LD start/stop call upon grid/genset in off mode added.
3- Command timer added.
4- Support of load meters.
5- Fuel level sensor added.
6- Fuel level alarm added
7- Common Modbus Master communication alarm added.
8- Support of Soluzione Solare Envmeter PRO added.
9- Support of Kippzonen SMP-series added.
10- Support of Sungrow COM100E (Logger1000 & Logger3000).  
11- Support of Woodward LS-5 as IO module.
12- Soluzione Solare configurator added (service tool).
13- Modbus Tester updated to support device scanner (service tool).  

************************************************
Version 1.03.1 based on version 1.03.0
************************************************
Corrections:
1- Power meter page was not working correctly in simulation.
2- Battery start/stop was logged as PV start/stop in event log.

************************************************
Version 1.03.2 based on version 1.03.1
************************************************
1- Handling of backup file was missing power meter settings.

************************************************
Version 1.04.0 based on version 1.03.2
************************************************
New features:
1- Support of Fuel pressure sensor readout added.
2- Support of BDSensor DCL531 added.
3- Scaling option added to Fuel level and Fuel pressure sensor handling via EClogic.
4- Command panel interface added. 
5- Load meter data made possible to use for control routine.

************************************************
Version 1.04.1 based on version 1.04.0
************************************************
1- Update made to the charge handling when parallel to grid operation.
2- Update made to the Ramp Interlock routine.
3- Update made to the Mega-TS support. 

************************************************
Version 1.04.2 based on version 1.04.1
************************************************
1- OCC/OGC set to 0kW when battery is offline. 
2- PV GC on EC web was not POA/BOM compensated. 
3- Update made to the Ramp Interlock routine.

************************************************
Version 1.04.3 based on version 1.04.2
************************************************
1- Update to PV charge.

************************************************
Version 1.04.4 based on version 1.04.3
************************************************
1- Battery communication alarm will trigger backup of grid. (Megarevo only).

************************************************
Version 1.04.5 based on version 1.04.4
************************************************
1- Megarevo protocol updated.

************************************************
Version 1.04.6 based on version 1.04.5
************************************************
1- Battery communication alarm will no longer trigger backup of grid. (Megarevo only).

************************************************
Version 1.04.7 based on version 1.04.6
************************************************
1- BMS/PCS state and event flags are added to event log. 

************************************************
Version 1.05.0 based on version 1.04.7
************************************************
1- Update of backend. 

************************************************
Version 1.06.0 based on version 1.05.0
************************************************
1- Support of SCU inverter
2- Support of EcpvX cluster
3- PV charge function updated

************************************************
Version 1.07.0 based on version 1.06.0
************************************************
1- Boot and service tool updated.

************************************************
Version 1.08.0 based on version 1.07.0
************************************************
1- Added SinExcel protocol.
2- Added Atess protocol.
3- Support of multiple Smartloggers and InverterManagers including data acquisition.
4- Load meter now supported in Simulation mode.

*****************************************************
Version 1.09.0 based on version 1.08.0
*****************************************************
1- Support of WindMeter from Soluzione Solare added.
2- Windspeed now displayed with one decimal.
3- Settings for Panel degradation, DC losses and AC losses are added to the PV generating capacity scheme.
4- SDMO APM802 support added.
5- Chint 14_36kW support added.
6- Chint SCA 18_36kW support added.
7- Sofar 80_136kW support added.
8- Weekday added to Command timers.
9- Config read fail could be provoked unexpectedly.
10- Eventlog handling updated. 

*****************************************************
Version 1.09.1 based on version 1.09.0
*****************************************************
1- Updated SCU protocol. 

*****************************************************
Version 1.09.2 based on version 1.09.1
*****************************************************
1- Updated SCU protocol.   

*****************************************************
Version 1.09.3 based on version 1.09.2
*****************************************************
1- Updated SCU protocol.

*****************************************************
Version 1.10.0 based on version 1.09.3
*****************************************************
1- DNP3 reference for battery added.
2- Sungrow COM100E protocol updated.
3- Cummins PCC updated.
4- Generating capacity for grid is now calculated when fixed on is selected.
5- Megarevo event log updated.

************************************************
Version 1.11.0 based on version 1.10.0
************************************************
1- Support of Moura BESS.
2- Support of WEG SIW750.
3- Support of PV control selection "P ONLY" added.
4- Support of inverter acquisition when using the Sungrow COM100E protocol added.
5- Support of meteo acquisition from a PC-4 when using the Sungrow COM100E protocol added.
6- Update of SPM32/SPM33 meter handling in case of presence of PTs.
7- "Save to flash" handling added for Soluzione Solare sensor configuration (Service Tool).

************************************************
Version 1.11.1 based on version 1.11.0
************************************************
1- SCU protocol updated.
 
************************************************
Version 1.12.0 based on version 1.11.1
************************************************
1- Support of SGC120/121 
2- Support of SunMeter Pro WIND (with one decimal display). 
3- BOM offset added
4- DFUN DFPM93 power meter support added
5- WEG 750SIW inverter protocol added.
6- All PWMet sensors are now supported.
7- DEYE inverter protocol added.
8- Acuvim L protocol updated.
9- Reading of grid/genset production from SCU GRES added.
10- Seperate uptium genset operating point added as BESS reference.
11- Overall min/max SOC levels for when discharge/charging is suppressed. 

************************************************
Version 1.13.0 based on version 1.12.0
************************************************
1- 4pcs of EClogic alarms added.
2- Minimum load threshold for PV to start charge ip updated. 

************************************************
Version 1.13.1 based on version 1.13.0
************************************************
1- Battery status bits added to modbus.
2- EClogic alarms handling updated.

************************************************
Version 1.14.0 based on version 1.13.1
************************************************
1- Seamless transfer option added.
2- Send mode (PQ/VF) option added.
3- ABB TRIO protocol updated.
4- EClogic timers added.

************************************************
Version 1.14.2 based on version 1.14.0
************************************************
1- Ready flag changed for SCU protocol.
2- WEG protocol updated.

************************************************
Version 1.14.3 based on version 1.14.2
************************************************
1- WEG protocol updated.

************************************************
Version 1.14.4 based on version 1.14.3
************************************************
1- Modbus RTU scheduler updated for Battery RTU inverter.
2- WEG protocol updated. 
3- Optium percentage feature updated.

************************************************
Version 1.14.5 based on version 1.14.4
************************************************
1- Internal protocol from EcpvX slave to cluster updated.

************************************************
Version 1.15.0 based on version 1.14.5
************************************************
1- Sensitivity handling of Modbus Master alarms added.

************************************************
Version 1.15.1 based on version 1.15.0
************************************************
1- COM3 line initialization updated.

************************************************
Version 1.15.2 based on version 1.15.1
************************************************
1- Backup handling updated.

************************************************
Version 1.16.0 based on version 1.15.2
************************************************
1- Inverter power production deviation alarm support added.
2- Inhinitation of inverter communication alarms based on night condition and/or low POA condition support added.
3- Lettel MCX-34V support added.
4- Change made to Acuvim L handling.

************************************************
Version 1.16.1 based on version 1.16.0
************************************************
1- Modbus TCP on Power meter and IO communication updated.
2- Modbus Master sensitivity scheme for superior loggers like Smartlogger and COM100E updated.
3- EClogic Modbus Events added.
4- Correction made to Acuvim L handling.

************************************************
Version 1.17.0 based on version 1.16.1
************************************************
1- Dedicated fail class for the ESS added.
2- Update made to handling of "Control ID/IP" readings.
3- Update made to minimum genset load handling.
4- Update made to Alarm Signal handling.

************************************************
Version 1.18.0 based on version 1.17.0
************************************************
1- Support of Sungrow ST129CP_50HV added.
2- Settings for handling of PCS mode to use in the various operating conditions added.

************************************************
Version 1.19.0 based on version 1.18.0
************************************************
1- Provision for BMS support added.
2- Polyntech BMS support added.
3- Greentech Caprack BMS support added.
4- Sinexcel PWS1/PWG2 support added.
5- Cell voltage min/max alarms added.
6- Cell voltage min/max channel included in PCS communication added.
7- Cell temperature min/max channel included in PCS communication added. 
8- SunSpec handling updated.
9- Moura handling updated.

************************************************
Version 1.19.1 based on version 1.19.0
************************************************
1- Moura handling updated.

************************************************
Version 1.19.2 based on version 1.19.1
************************************************
1- Modbus Master sensitivity scheme for superior loggers like Smartlogger and COM100E updated.
2- Update made to the Lettel MCX-34V handling.

************************************************
Version 1.19.3 based on version 1.19.2
************************************************
1- PV generating capacity is now set to 0kW in case it is night time and the generating capacity method is set to OFF. 
2- Update made to discharge timer based scheme handling.

************************************************
Version 1.19.4 based on version 1.19.3
************************************************
1- Update made to discharge timer based scheme handling.

************************************************
Version 1.20.0 based on version 1.19.4
************************************************
1- Datakom D300_500_700 support added.  
2- TCP Client handling updated.

************************************************
Version 1.20.1 based on version 1.20.0
************************************************
1- Update made for the ST129CP_50HV support.

************************************************
Version 1.21.0 based on version 1.20.1
************************************************
New features:
1- Grid & DG Charge refernces added. 
2- Charge scheduler added.
3- InteliGen_4_200 support added.
4- InteliMains_210 support added.
5- Rica RK200 and RK220 support added.

************************************************
Version 1.21.1 based on version 1.21.0
************************************************
1- Update made for the ST129CP_50HV support.

********************************
Version 1.21.2 based on version 1.21.1
********************************
1- Greentech handling updated.
2- The buttons for going to inverter data 17-32 was not taking inverter cluster into consideration
causing the page to be hidded when not supposed to.  
3- Mains readings was not shown on Overview page if it came from "PV_COMM".
4- Mains readings was not shown on Overview page if it came from "MODBUS PAGE 03".
5- DG readings was not shown on Overview page if it came from "MODBUS PAGE 03".
6- Update made to reboot handling.

************************************************
Version 1.22.0 based on version 1.21.2
************************************************
1- Support of SMA Data Manager added.
2- PowerCombo 20C1H1000K support added.
3- INVT XG support added.

************************************************
Version 1.22.1 based on version 1.22.0
************************************************
1- Update made to INVT XG support.

************************************************
Version 1.23.0 based on version 1.22.1
************************************************
1- Monitoring of DC coupled PV via BESS support added.
2- Monitoring of DC coupled PV from SCU GRES added.
3- Monitoring of DC coupled PV from Sinexcel PWG2 added.

************************************************
Version 1.23.1 based on version 1.23.0
************************************************
1- Reactive power control support for Sofar 80-136 added.
2- Sofar 80-136 inverter start/stop command added.

************************************************
Version 1.24.0 based on version 1.23.1
************************************************
1- Increased from 4 to 8 EClogic alarms.
2- Updates made to the ECpvX Cluster support.
3- Updates made to the GRES support.
4- Updates made to the PowerCombo 20C1H1000K support.
5- Updates made to the SMA DataManager support.

************************************************
Version 1.24.1 based on version 1.24.0
************************************************
1- Updates made to the GRES support.

************************************************
Version 1.25.0 based on version 1.24.1
************************************************
New features:
1- Acrel ADL3000-E support added.
2- NR PCS-9765 support added.
3- Support af Kgooer BAMS added.
4- All "No alarm" logs generated at power up are now suppressed.
5- Load icon and busbar lines is now green in case genset or grid is connected.
6- SMA Datamanager number of decimals to use for control commands can now be set via settings.
7- Update made for Ginlong Solis.

************************************************
Version 1.26.0 based on version 1.25.0
************************************************
1- Support of HVAC system interface added.
2- Support of BlackShield ACP added.

************************************************
Version 1.27.0 based on version 1.26.0
************************************************
1- Grid tranformer load limit added for discharging situation.

************************************************
Version 1.27.1 based on version 1.27.0
************************************************
1- EClogic alarm texts handling updated.
2- Greentech Caprack protocol updated.
3- Sinexcel PWS1 and PWG2 protocols updated.
4- Update made to Kgooer BMS handling.
5- Modbus Slave handling updated.

************************************************
Version 1.27.2 based on version 1.27.1
************************************************
1- Modbus data for total number and number of secondary inverters present in the plant where not correct.

************************************************
Version 1.27.3 based on version 1.27.2
************************************************
1- Greentech caprack support updated.
2- Sinexcel PWS1/PWG2 support updated.
 
************************************************
Version 1.27.4 based on version 1.27.3
************************************************
New features:
1- Genset Mode activate/deactivate accessible via EClogic.
2- Grid Mode activate/deactivate accessible via EClogic. 
3- MegaRevo support updated.
4- Presence of external producer handling updated.

************************************************
Version 1.27.5 based on version 1.27.4
************************************************
1- Wrong sign on power reference was used for grid capacity charging check in Fixed P SA mode.
2- Available mains power in battery was figuring as Available PV power in battery. 

************************************************
Version 1.28.0 based on version 1.27.5
************************************************
1- Setting for BMU to use for reading out pile/stack SOC added.
2- NTP sync alarm is now self-acknowledging.

************************************************
Version 1.29.0 based on version 1.28.0
************************************************
1- Selection for displaying the relative or total load and grid and genset powers.
2- EFC counter handling updated.
3- Smartlogger handling updated.

********************************
Version 1.29.1 based on version 1.29.0
********************************
1- Active power for individual phases included in the Huawei power meter protocol support.
2- Update made to the Carlo Gavazzi EM300 handling.
3- Update made to the Datakom D300-700 handling.
4- The "Sync-SR" routine is updated.
5- The WEG SIW750 handling is updated.

************************************************
Version 1.30.0 based on version 1.29.1
************************************************
1- PV charge priority selection for grid parallel operation added.
2- PV charge priority selection for genset parallel operation added.
3- PV reference setting when only parallel with battery added.
4- Charging limit from BMS/PCS can now be overruled.
5- Disharging limit from BMS/PCS can now be overruled.
6- Support for Selec MFM384 added.
7- Support for MICS CBMS added.
8- Default value for SunSpec P and Q control enable transmission is changed from Continuous to Disable.

************************************************
Version 1.30.1 based on version 1.30.0
************************************************
1- Default setup for COM2 and COM3 changed.
2- Default setup for NTP changed.
3- Sinexcel PWS2 support updated.
4- DSE GenComm. support updated.
5- MICA CBMS support updated.

************************************************
Version 1.30.2 based on version 1.30.1
************************************************
1- Log handling updated.

************************************************
Version 1.30.3 based on version 1.30.2
************************************************
1- Megarevo handling updated.

************************************************
Version 1.31.0 based on version 1.30.3
************************************************
1- Support for SAH XY-MD02 added.
2- Deye handling updated.

************************************************
Version 1.31.1 based on version 1.31.0
************************************************
1- Update made to charge handling.

************************************************
Version 1.32.0 based on version 1.31.1
************************************************
1- Huawei Smartlogger added as PCS protocol for LUNA2000 interface.
2- SMA DataManager added as grid power meter selection.
3- Update made to ATESS PCS handling.

************************************************
Version 1.33.0 based on version 1.32.0
************************************************
1- Huawei Smartlogger - PV, added as PV protocol.

************************************************
Version 1.34.0 based on version 1.33.0
************************************************
1- Support for battery power meter added.
2- Option of using fixed CT/VT settings for SPM32 and SPM33 added.

************************************************
Version 1.35.0 based on version 1.34.0
************************************************
1- Support for Cummins MCM3320 added.
2- Support for Cummins Sices MC200/MC400 added.
3- ATESS PCS support updated.

************************************************
Version 1.35.1 based on version 1.35.0
************************************************
1- Grid readings via SMA DataManager updated.

************************************************
Version 1.35.2 based on version 1.35.1
************************************************
1- Update made to sensor handling.

************************************************
Version 1.36.0 based on version 1.35.2
************************************************
1- Spot price read added.
2- Spot price arbitrage optimizing routine added.
3- SOC now updated in simulation mode based on the BESS power.
4- Update made to Deye support handling.

************************************************
Version 1.36.1 based on version 1.36.0
************************************************
1- Minimum profit setting for spot price arbitrage added.
2- Germany-Luxembourg, France and Austria added to spot price market list.

************************************************
Version 1.36.2 based on version 1.36.1
************************************************
1- Germany and Luxembourg split up in two seperate market selections.

************************************************
Version 1.37.0 based on version 1.36.2
************************************************
1- ECsync support added.
2- Setting for Max PV dispatch limit when parallel with battery added.
3- Megarevo handling support updated.

************************************************
Version 1.37.1 based on version 1.37.0
************************************************
1- ECsync modbus updates.

************************************************
Version 1.37.2 based on version 1.37.1
************************************************
1- Clock handling updated.

************************************************
Version 1.37.3 based on version 1.37.2
************************************************
1- The minimum daily profit threshold converted to a minimum profit per charge/discharge sequence threshold to prevent the spotprice arbitrage optimizer reacting on small valleys/peaks.

************************************************
Version 1.37.4 based on version 1.37.3
************************************************
1- ECsync log handling updated.

************************************************
Version 1.37.5 based on version 1.37.4
************************************************
1- Huawei Smartlogger BESS handling updated.

************************************************
Version 1.37.6 based on version 1.37.5
************************************************
1- Genset and Grid backup capacity handling updated.

************************************************
Version 1.37.7 based on version 1.37.6
************************************************
1- Huawei Smartlogger BESS handling updated.

************************************************
Version 1.38.0 based on version 1.37.7
************************************************
1- Multiple P(f) curve support added.
2- NEM support for LER units added.
3- AEM support for LER units added.
4- Support for PowerCombo-20C1H1200K added.
5- Solax X3-MEGA and G2G3-FORTH support added.

************************************************
Version 1.38.1 based on version 1.38.0
************************************************
2- SCU BRES handling updated.

************************************************
Version 1.39.0 based on version 1.38.1
************************************************
1- Fast control command support added for fulfilling ancillary service requirements.
2- Support for Megarevo MPS added.

************************************************
Version 1.39.1 based on version 1.39.0
************************************************
1- Update made to the PowerCombo 1200 handling.

************************************************
Version 1.40.0 based on version 1.39.1
************************************************
1- Option added for sending stop cmd to the BESS in case of 0kW reference while not being off-grid.
2- "Mains reading" added to the list for PV and Battery "kW Origin" options.

************************************************
Version 1.41.0 based on version 1.40.0
************************************************
1- Include PV energy while grid parallel in CO2 saving calculation.
2- Same cosphi option added to Mains Q CTRL. 
3- Limit option for RRCR added. 

************************************************
Version 1.41.0 based on version 1.40.0
************************************************
1- NR PCS 9567 PCS support updated.

************************************************
Version 1.42.0 based on version 1.41.0
************************************************
1- Added support for Kehua BCS Series PCS
2- Added support for Alpha ESS PCS

************************************************
Version 1.43.0 based on version 1.42.0
************************************************
1- Added support for PAN BMS PLD09
2- Greentech Caprack support updated

************************************************
Version 1.43.1 based on version 1.43.0
************************************************
1- Support for Lufft WS200 meteo sensor.
2- BRES support updated.

************************************************
Version 1.44.0  based on version 1.43.1 
************************************************
1- Support added for Ingeteam 3Play.
2- Update made to Huawei BESS support. 
3- Closed loop PID option added for PCS control.

************************************************
Version 1.44.1 based on version 1.44.0 
************************************************
1- Minimum valley/peak profit replaced by full charge cost factor in the Arbitrage handling.

************************************************
Version 1.44.2 based on version 1.44.1 
************************************************
1- Update made to the display of arbitrage profit profile.

************************************************
Version 1.45.0 based on version 1.44.2 
************************************************
1- ECgrid support added.
2- Two P(f) supported and reserved for PV and battery respectively.
3- Two Q(U) supported now and they are reserved for PV and battery respectively.
4- NEM/AEM support removed.
5- Greentech Caprack support updated.
6- PAN_BMS_PLD09 support updated.

************************************************
Version 1.45.1 based on version 1.45.0 
************************************************
1- Update made to inverter cluster capacity editing.

************************************************
Version 1.46.0 based on version 1.45.0 
************************************************
1- Support added for LogicsPowerAMR PYRA 300V
2- Support added for Growatt WIT
3- Support added for Poweroad GSSTES

************************************************
Version 1.46.1 based on version 1.46.0 
************************************************
1- Fixed PV power meter not working alone.
2- Fixed a bug with Pilot SPM33 Powermeter. 

************************************************
Version 1.47.0 based on version 1.46.1 
************************************************
1- Added support for Siemens Smart Meter 7kt0310
2- PID closed loop control for PV inverters added
3- Changed Power Factor calculcation for Growatt inverters and Growatt PCS.

************************************************
Version 1.48.0 based on version 1.47.0 
************************************************
1- Support added for IME Nemo96EA power meter

************************************************
Version 1.48.1 based on version 1.48.0 
************************************************
1- Update made to HUawei Smartlogger support.

************************************************
Version 1.49.0 based on version 1.48.1 
************************************************
1- Added EClogic Functions to overwrite PV and Battery References.
2- Added EClogic function to overwrite PV Charge Priority setting.
3- DNP3 protocol adjustments.

************************************************
Version 1.50.0 based on version 1.49.0 
************************************************
1- Added support for Comap InteliGen 1000 Genset Powermeter
2- Encombi DG Group power meter protocol enables grouping of mulitple Gensets under one ECpv2 in order to combine more than 16 Gensets per site.
3- ECev support added

************************************************
Version 1.51.0 based on version 1.50.0 
************************************************
1- Option to turn off unused Modbus frames from Power meters
2- Added STS position handeling for SCU GRES

************************************************
Version 1.52.0 based on version 1.51.0 
************************************************
1- Two advanced grid support options added. 

************************************************
Version 1.53.0 based on version 1.52.0 
************************************************
1- Added support for Deye Hybrid inverter as PCS. 

************************************************
Version 1.54.0 based on version 1.53.0 
************************************************
1- Added EClogic cmd registers to overwrite Mains control modes. 

************************************************
Version 1.55.0 based on version 1.54.0 
************************************************
1- Support for Afore PV inverter added. 
2- Fixed a problem that caused the PV reference to be doubled.

************************************************
Version 1.56.0 based on version 1.55.0 
************************************************
1- PV and Battery PREF/QREF can now be written to via Modbus page02.
2- Huawei Smartlogger BESS support updated.

************************************************
Version 1.57.0 based on version 1.56.0 
************************************************
1- ECsync breaker open/close command via EClogic added.
2- Suppress commands of varios battery control function via EClogic added.

********************************
Version 1.57.1 based on version 1.57.0
********************************
1- IO socket alarm log handling improved were not handled correctly.
2- Update made to the DFPM93 support.

********************************
Version 1.57.2 based on version 1.57.1
********************************
1- Limit of the AC power out from the BESS to the DC coupled PV power production via EClogic handle added.
2- Common comm. alarm was not triggered by battery inverter alarms or battery power meter alarms.
3- Update made to the DFPM93 support.

********************************
Version 1.57.3 based on version 1.57.2
********************************
1- Update made to the SevenSensor support.

********************************
Version 1.58.0 based on version 1.57.3
********************************
1- Support added for WEG MMW03 power meter.
2- Support added for Meier Energy CMM62 power meter.
3- Support added for Growatt VPP PV inverter. 

************************************************
Version 1.58.1 based on version 1.58.0
************************************************
1- Start/stop of PV via EClogic added.
2- Start/stop of battery via EClogic added.
3- Open/close of ECsync without also setting ECweb buttons via EClogic added.
4- Textual corrections.

************************************************
Version 1.59.0 based on version 1.58.1
************************************************
1- Support for Renepoly BESS added.

************************************************
Version 1.59.1 based on version 1.59.0
************************************************
1- Removed the ability to send mails.

************************************************
Version 1.60.0 based on version 1.59.1
************************************************
1- Support added for Jinko SUNGIGA PCS.
2- Support for EClogic event via ECgrid (ECapi) added.
3- Support added for DMeters DM1000 Power meter.

************************************************
Version 1.61.0 on ECpvX Version 1.60.0
************************************************
1- Support for ECapi POST commands added.
2- Update made to the Schneider PM2XXX support.

************************************************
Version 1.61.1 based on version 1.61.0
************************************************
1- Update made to Greentech Caprack handling.

************************************************
Version 1.62.0 based on version 1.61.1
************************************************
New features:
1- Support for RICA330 added.
2- Support for Meatrol ME337 added.
3- Support for Crown Voltmore added.

************************************************
Version 1.63.0 based on version 1.62.0
************************************************
1- Support for Growatt ShineMaster X added.
2- Support for WEG BIW610 added.
3- Support for Legrand EMDX3 power meter added. 

************************************************
Version 1.63.1 based on version 1.63.0
************************************************
1- Improved ramping accuracy on PV and Battery inverter setpoints.
2- Added DCPV compatibility to ECev Modbus page.

************************************************
Version 1.64.0 based on version 1.63.1
************************************************
1- Support added for EcoSolys Elite-S series inverters.
2- Support added for Weiheng EMS100. 
3- Support added for Enjoy EPCS105-AM PCS. 
4- Support added for Poweroad CMBS.
5- RRCR can now be enabled and disabled for PV and BESS seperately. 

************************************************
Version 1.64.1 based on version 1.64.0
************************************************
1- Adjustments made to SEM-X protocol.
2- Adjusted Renepoly emergency stop behavior

************************************************
Version 1.65.0 based on version 1.64.1
************************************************
1- Support added for MEIER CMM72 power meter.
2- PV reading and Battery reading can now be used as origin for the mains power.
3- Adjustments made to SmartGen HGM7X00_9X00 power meter protocol.
4- Adjustments made to SEMX power meter protocol.

************************************************
Version 1.66.0 based on version 1.65.0
************************************************
1- On-grid/Off-grid inverter settings scheme added.
2- Added Mains Production measurement to MegaRevo MPS protocol. 
3- Battery Q ctrl mode added for when Battery is off-grid and parallel to PV only. 
4- Adjusted SEM-X BESS and PV control frames
5- Growatt SEM-X power meter protocol removed.